Exclusive handmade knives No. 1 in Ukraine
Every day, 24/7
No days off
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC
BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC

BEARD exclusive hand-made ax by Serhiy Dytyuk, Steel - 65G, 54 - 58 HRC

Загальна довжина клинка mm: 155 mm +- 5 mm
Матеріал леза The blade - steel 65G - is a wear-resistant, viscous, strong, elastic material, with good tear resistance and resistance to shock loads.
Твердість клинка (метал): Hardness - 54 - 58  HRC
Матеріал руків'я: Dried WALNUT. (If you wish, you can make a handle of similar hard rocks: ash or acacia).
Довжина леза 235 +-5 mm
  • Availability: Під замовлення
1,100.00 грн.
Order in 1 click
We will call you back and clarify the details
Sheath

Description

SPECIFICATIONS:

The name of the ax is BEARD exclusive hand-made ax by Serhiy Dytyuk buy order in Ukraine (Steel - 65G)
Ax type: Handle
Brand: Studio of exclusive hand-made axes SERGIA DITYUKA


Complete set: (Behind the zamovnik's bazhanny)

VIP case made of hard wood, covered with furboy and additional firm varnish: 4200 UAH
The box is standard, singed from pine: 2300 UAH
Subscription for juice: 1500 UAH


Main characteristics of the ax: 

Steel grade: The blade - steel 65G - is a wear-resistant, viscous, strong, elastic material with good tear resistance and resistance to shock loads.
Blade shape: Rounded
 
Ax head material: carbon steel hardened 54 - 58 HRC
Processing: grinding, polishing, firing
Blade sharpening angle: 30-35 degrees
Grinding of the blade: Finish - grinding before etching with 600 grain, after etching - with 1000 m grain.
Blade length: 235 +-5 mm
Length from the butt of the ax to the cutting edge: 155 mm +- 5 mm
The thickness of the shoe:  25 mm +- 2 mm
Head weight:  830 +-30 grams
Total weight:  1050 +- 30 grams
Length of the handle: 460 +-10 mm
Total length: 500 mm
Handle material: Dried WALNUT. (If you wish, you can make a handle of similar hard rocks; ash or acacia). 
Cover (sheath): Italian vegetable-tanned genuine leather, 3-3.5 mm thick, stitched with waxed thread. Manual embossing of the invoice or inscription (possible upon request from your drawing).
Copper plated tool:   No
Rubberized handle:  No
Ax type: Universal
 
Additional characteristics:
Cutting edge: Polished
 

MASTER'S COMMENTS:

How to care for an ax: dear customers, given that axes are made of steels that do not have protection against corrosion, it is advisable to lubricate the blade after use with either a vegetable oil or a universal oil in the form of a spray, after which the oil should be allowed to dry a little and thoroughly wiped But if you don't like the appearance of the ax over time, it's easy to fix it: it's enough just to pass the blade with a 600-grit abrasive leather, wipe off all the dust after processing, and lubricate it with vegetable oil or universal oil like WD-40.

Dear customers, please note that all products are made purely by hand and have a unique individual character. That is, the appearance of the product (shade and structure of wood, depth of metal etching, leather texture, etc.) may differ slightly from the photo, but in general, the product will be as close as possible to the photo in the product card. Thanks for understanding!"


Model: BEARD exclusive hand-made ax by Serhiy Dytyuk buy order in Ukraine (Steel - 65G)
Model number: 018
Country of birth: Ukraine
Craftsman: Master Sergiy Dityuk, Dnipro, Ukraine, Studio of  exclusive handmade axes SERGIY DITYUK
Best use: Multifunctional : hunting, fishing, dividing the carcass, chopping firewood, clearing the area, etc


A sharpened ax is not a melee weapon.


Our axes are very sharp, so be very careful when opening and using them. We are not responsible for any injuries resulting from the use of our axes.
Our products are intended for legal use only by responsible buyers. We will not sell our products to anyone under the age of 18.


Availability changes regularly, after confirming your order we will notify you of availability or when the item is ready. The product may differ slightly from the one shown in the photo.


 

Steel 65G: Properties, applications and features

This is a high-strength structural material that has found wide application in various industries. It has high wear resistance, high temperature resistance and good weldability.

2. Composition and properties of steel 65G

2.1 Chemical composition

 

Element Content
Carbon (C) 0.62-0.70%
Silicon (Si) 0.17-0.37%
Manganese (Mn) 0.9-1.2%
Chrome (Cr) 0.8-1.1%
Molybdenum (Mo) 0.15-0.25%
Phosphorus (P) no more than 0.035%
Sulfur (S) no more than 0.035%

 

2.2 Mechanical properties

  • Tensile strength - 650 MPa;
  • Temporary resistance - 590 MPa;
  • Relative elongation at break - not less than 13%;
  • Relative narrowing at break - not less than 50%;
  • Brinell hardness - not less than 207 HB.

 

Mechanical properties of steel 65G

Index Meaning
Tensile strength 880-1180 MPa
Yield strength 680-980 MPa
Elongation at break 12-16%
Relative narrowing of the cross section 30-60%
Impact strength at t=20°С 12-16 J/cm²
Hardness 179-269 NB

 

3. Application of steel 65G

3.1 Construction industry

It is widely used in the construction industry. It is used for the manufacture of structural elements that must withstand high loads, for example, for the production of bridge structures, railway overpasses, as well as for the construction of building foundations.

3.2 Mechanical engineering

It is used in mechanical engineering for the manufacture of parts that can withstand high loads and require increased strength and wear resistance. This steel is widely used in the manufacture of gears, shafts, nuts, bolts and other parts.

3.3 Pipe production

Also used in the production of pipes. It is used to produce pipes that withstand high pressure and require increased strength and wear resistance.

The use of steel 65G and heat treatment of products:  spiral springs, sheet and spring washers are made from steel 65G and other spring steels. Spring steel is used to make springs. The hardness of the springs is within R c  = 40-50, and spring washers R c  = 40-48. Upon acceptance, the springs are checked for hardness and elasticity. The test method should, as far as possible, approximate the actual operating conditions of the springs (tension, compression or bending).

Springs made of heat-treated (patented) wire or tape of classes H, P and B undergo additional tempering at a temperature of 250-350 ° to relieve internal stresses that have arisen during their manufacture and to improve the elastic properties of the wire.

Spring release is best done in saltpeter baths for 5-10 minutes, depending on the cross section of the material. When tempering in oil or electric furnaces, special attention should be paid to the uniformity of heating. Vacation time in these furnaces is 20-40 minutes.

Springs made of annealed steel are quenched and tempered. In the case of making springs from wire with a diameter of more than 6 mm, high tempering is carried out before hardening at a temperature of 670-720 ° to eliminate cold hardening resulting from cold winding. Hot-wound springs are normalized before hardening.

For heating for quenching, the springs are placed in chamber furnaces or salt baths heated to the required temperature. To avoid deformation, large springs are heated in a special device.

Small springs are loaded into the oven on a baking sheet. Exposure in the furnace should be the smallest - to prevent oxidation and decarburization. To reduce the residence time in the oven, small springs are placed on a preheated baking sheet. In the absence of a protective atmosphere in the furnace, the springs are packed in an insulating environment, or small amounts of charcoal are thrown into the furnace. Cool the springs in oil. It is not recommended to cool the springs in water to avoid cracking. If hardening in water is necessary, the exposure should be no more than 2-3 seconds. followed by cooling in oil.

Before release, the springs are cleaned of oil by washing in a soda solution or thoroughly rubbing in sawdust. Oil that is not removed from the springs flares up during tempering and changes the tempering conditions, which leads to uneven heating and low hardness. The tempering temperature is 300-420°. The annealing of the extreme turns is carried out in a lead bath.

Large springs are put on pipes before release to eliminate warpage.

Attention should be paid to the surface of the material used for the manufacture of springs. Risks, hair lines and other defects lead to the formation of cracks, and the decarburized layer leads to a decrease in the elastic properties of the spring.

Quite often, anti-corrosion coatings used on a number of springs make them brittle due to the saturation of the metal with hydrogen during pickling and during the coating process. This is especially noticeable on springs made of wire or tape of small cross section. This brittleness, called etching or hydrogen, is eliminated by heating the finished springs in oil, glycerin or an oven at a temperature of 150-180 ° for 1-2 hours.

However, during prolonged etching, the metal is saturated with hydrogen so strongly that the specified temperature does not eliminate brittleness and the springs must be annealed. To avoid deep hydrogenation, springs made of thin wire or tape should not be pickled before coating, but should be sandblasted and heated after coating, as indicated above.

4. Features of the use of steel 65G

4.1 Weldability

It has good weldability. However, when welding, certain rules must be observed in order to avoid possible defects in the weld.

4.2 Processing

It has a high hardness, which can make it difficult to process. To facilitate the machining process, it is recommended to use carbide tools.

4.3 Corrosion resistance

Possesses average corrosion resistance. To increase its corrosion resistance, it is recommended to use protective coatings such as primers or paints.

 

5. Advantages of using 65G steel

  • High strength and wear resistance;
  • Good weldability;
  • Resistant to high temperatures;
  • Wide application in various industries;
  • Relatively low cost compared to other high strength materials.

It is worth remembering that if you use the ax for its intended purpose and with careful handling, the ax will serve you for a very, very long time

 
Walnut wood has good physical and mechanical properties
 
Walnut wood has good physical and mechanical properties - it is quite dense and strong, and can be easily processed with both machine tools and hand tools. Reliability, as well as high decorativeness and adaptability to various external conditions have made walnut a popular carpentry material not only on the continent, but also around the world. American walnut is widely used to create almost any wooden products, which differ in both aesthetics and durability.
Walnut wood has a dark color in chocolate-brown tones, sometimes with a slight purple tint. Its noble texture is highly valued when creating handmade products. High-quality sanding and colorless finish coating emphasize the expressive pattern and color of the wood even more.
Processing American walnut is usually not difficult. It is well cut and planed with a sharp tool, perfectly sanded and polished to a shine. Holds small parts well - walnut products can be covered with fine artistic carvings. Any product for wood is suitable for protective impregnation of black walnut. It is not accepted to tint and paint it, because the natural color range is appreciated in wood.
American walnut is strong, tough and heavy enough to be used for axes. Its wear resistance allows you to create axes for active use in adverse weather conditions. However, American walnut is not suitable for making a pickaxe with a long, narrow ax or a heavy hammer. It is ideal for small work tools and collectibles.
Examples of American walnut wood products
The noble colors and expressive texture of the walnut will perfectly decorate the hand-made collectible axes:
American walnut is well suited for creating axes of small working axes:
Of course, the blank format is suitable not only for making axes. For example, a flute can be made from a bar, and American walnut has excellent acoustic characteristics:

High-quality and original steel inlays are a wonderful decoration of exclusive and unique axes of the studio Studio of exclusive hand-made axes SERGIY DITYUKA (Ukraine), which offers to order and buy online store https://knife.net.ua


Related Products

Delivery and payment

Delivery and payment
Delivery by Nova Poshta
The speed of delivery to any branch of Nova Poshta in Ukraine is fixed by the operator, but usually does not exceed 1-3 calendar days.

In cash
Cash payment upon receipt of goods.
Cash on delivery at Nova Poshta (you must have a passport or driver's license with you).

Visa and MasterCard
Payment of the order to a Privat Bank card.
Delivery of goods is possible only after confirmation of payment.

Reviews (0)

Write a review

Note: HTML is not translated!
    Bad 
 Good